Article

Raheem, A.T. and Aziz, A.R.A. and Zulkifli, S.A. and Ayandotun, W.B. and Baharom, M.B. (2024) Development and Validation of a Free Piston Engine Linear Generator Simulation Model Including Cycle-To-Cycle Variation and Ignition Timing Sub-Models. Lecture Notes in Mechanical Engineering. pp. 239-254. ISSN 21954356

Ismael, M.A. and Rosli, M.A.F. and Aziz, A.R.A. and Mohammed, S.E. and Opatola, R.A. and El-Adawy, M. (2024) Gas to liquid (GTL) role in diesel engine: Fuel characteristics and emission: A review. Cleaner Engineering and Technology, 18.

Ali, A. and Aziz, A.R.A. and Ismael, M.A. (2024) Impact of injection pressures on properties, microscopic behavior, and microexplosions in biodiesel-emulsified fuel with biosurfactant. Applied Thermal Engineering, 248.

Munir, S. and Aziz, A.R.A. and Heikal, M. and Siddiqui, M.I. (2023) Combination of linear stochastic estimation and proper orthogonal decomposition: application in two-phase slug flow. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 45 (2). ISSN 16785878

Masri, M.M. and Aziz, A.R.A. and Ezrann, Z. and Zainal, A. and Mohammed, S.E. (2023) The Design and Simulation of an Exhaust Manifold for Free-Piston Linear Generator Engine. Lecture Notes in Mechanical Engineering. pp. 653-659.

Ahmed, M.I.I. and Baharom, M. and Aziz, A.R.A. (2023) The Effect of Curve Cylinder Liner on in-Cylinder Tumble Flow Motion Characteristic using CFD Port Flow Simulation. CFD Letters, 15 (10). pp. 186-205.

Nissar, Z. and Aziz, A.R.A. and Heikal, M.R. and Ismael, M.A. (2023) Experimental Investigation of Puffing/Microexplosion in Fuel Droplets and Effects of Injection Modes on It. Lecture Notes in Mechanical Engineering. pp. 147-160.

Rosli, M.A.F. and Ismael, M.A. and Aziz, A.R.A. and Mohammed, S.E. and A.B., O. and Opatola, R.A. (2023) Experimental study of Gas-To-Liquid (GTL) and diesel fuel blends evaporation behaviour and droplet lifetime through Leidenfrost effect. Energy Reports, 10. pp. 805-818.

Baharom, M.B. and Mohammed, S.E. and Hussain, N. and Aziz, A.R.A. and Zainal, Z.E.A. and Ismael, M.A. (2023) A Study on the Effect of Structural Properties and Configuration of Low-Stiffness-Resilient-Shaft (LSRS) on Torsional Behavior. Lecture Notes in Mechanical Engineering. pp. 995-1011. ISSN 21954356

El-Adawy, M. and Ismael, M.A. and Dalha, I.B. and Aziz, A.R.A. and El Maghlany, W. (2023) Unveiling the status of emulsified water-in-diesel and nanoparticles on diesel engine attributes. Case Studies in Thermal Engineering, 44.

Mukhtar N.A., M. and Hagos, F.Y. and Aziz, A.R.A. and Abdulah, A.A. and Karim, Z.A.A. (2022) Combustion characteristics of tri-fuel (diesel-ethanol-biodiesel) emulsion fuels in CI engine with micro-explosion phenomenon attributes. Fuel, 312. ISSN 00162361

Ayandotun, W.B. and Aziz, A.R.A. and Ismael, M.A. and Mohammed, S.E. and Raheem, A.T. (2022) Comparative assessment of the performance and combustion attributes of a free piston linear generator fuelled with CNG and CNG-CO2. Case Studies in Thermal Engineering, 38. ISSN 2214157X

Raheem, A.T. and Aziz, A.R.A. and Zulkifli, S.A. and Rahem, A.T. and Ayandotun, W.B. (2022) Development, Validation, and Performance Evaluation of An Air-Driven Free-Piston Linear Expander Numerical Model. Evergreen, 9 (1). pp. 72-85. ISSN 21890420

Raheem, A.T. and Aziz, A.R.A. and Zulkifli, S.A. and Baharom, M.B. and Rahem, A.T. and Ayandotun, W.B. (2022) Optimisation of operating parameters on the performance characteristics of a free piston engine linear generator fuelled by CNG�H2 blends using the response surface methodology (RSM). International Journal of Hydrogen Energy, 47 (3). pp. 1996-2016. ISSN 03603199

Bashir, A. and Zulkifli, S.A. and Aziz, A.R.A. (2022) Velocity-Based Control of Piston Trajectory in a Free-Piston Linear Electric Generator by Load Current Modulation. Lecture Notes in Electrical Engineering, 865. pp. 97-108. ISSN 18761100

Zainal A., E.Z. and Ismael, M.A. and Aziz, A.R.A. and Mohammed, S.E. and Baharom, M.B. and Firmansyah and Hanif Ibrahim, M. and Sahalan, M.I. and Qawiy, A. (2021) Effect of aspect ratio on frequency and power generation of a free-piston linear generator. Applied Thermal Engineering, 192. ISSN 13594311

Rosli, M.A.F. and Aziz, A.R.A. and Ismael, M.A. and Elbashir, N.O. and Zainal A., E.Z. and Baharom, M. and Mohammed, S.E. (2021) Experimental study of micro-explosion and puffing of gas-to-liquid (GTL) fuel blends by suspended droplet method. Energy, 218. ISSN 03605442

Ismael, M.A. and Aziz, A.R.A. and Mohammed, S.E. and Zainal A, E.Z. and Baharom, M.B. and Raheem, A.T. and Ayandotun, W.B. and Harith, F.I. and Khazaimah, I. (2021) Experimental study on combustion stability and performance of hydrogen-enriched compressed natural gas of a free-piston linear generator. International Journal of Hydrogen Energy, 46 (79). pp. 39536-39547. ISSN 03603199

Ismael, M.A. and Aziz, A.R.A. and Zainal A., E.Z. and Mohammed, S.E. and Ayandotun, W.B. and Baharom, M.B. and Sallehudin, M.S. and Syakirin R., M. and Anwerudin, A.R.T. and Masri, M.M. (2021) Investigation on free-piston motion and power generation of a dual-piston air-driven expander linear generator. Energy Reports, 7. pp. 2388-2397. ISSN 23524847

Reksowardojo, I.K. and Arya, R.R. and Budiman, B.A. and Islameka, M. and Santosa, S.P. and Sambegoro, P.L. and Aziz, A.R.A. and Abidin, E.Z.Z. (2020) Energy management system design for good delivery electric trike equipped with different powertrain configurations. World Electric Vehicle Journal, 11 (4). pp. 1-21. ISSN 20326653

Arman, A. and Hagos, F.Y. and Abdullah, A.A. and Aziz, A.R.A. and Mamat, R. and Cheng, C.K. and Vo, D.-V.N. (2020) Kinetic and CFD Modeling of Exhaust Gas Reforming of Natural Gas in a Catalytic Fixed-Bed Reactor for Spark Ignition Engines. Chemical Engineering and Technology, 43 (4). pp. 705-718. ISSN 09307516

Abdul Karim, Z.A. and Khan, M.Y. and Aziz, A.R.A. (2019) Evolution of Microexplosion Phenomenon in Parent-Child Droplets of Water in Biodiesel Emulsions Enhanced by Different Surfactant Dosages and Hydrophilic-Lipophilic Balance Values. Journal of Energy Resources Technology, Transactions of the ASME, 141 (10). ISSN 01950738

El-Adawy, M. and Heikal, M.R. and Aziz, A.R.A. (2019) Experimental investigation of the in-cylinder tumble motion inside GDI cylinder at different planes under steady-state condition using stereoscopic-PIV. Journal of Applied Fluid Mechanics, 12 (1). pp. 41-49. ISSN 17353572

El-Adawy, M. and Heikal, M.R. and Aziz, A.R.A. (2019) Stereoscopic particle image velocimetry measurements and proper orthogonal decomposition analysis of the in-cylinder flow of gasoline direct injection engine. Journal of Energy Resources Technology, Transactions of the ASME, 141 (4). ISSN 01950738

Foong, F.M. and Ket, T.C. and Lee, O.B. and Aziz, A.R.A. (2019) Stress and damping of wide cantilever beams under free vibration. Journal of Mechanical Science and Technology, 33 (1). pp. 21-27. ISSN 1738494X

Tariq, A. and Altaf, K. and Rani, A.M.A. and Baharom, M. and Aziz, A.R.A. (2019) Study of heat transfer attributes of custom fins for Crank-Rocker engine block using ANSYS. Journal of Advanced Research in Fluid Mechanics and Thermal Sciences, 62 (2). pp. 235-243. ISSN 22897879

Mukhtar, M.N.A. and Aziz, A.R.A. and Hagos, F.Y. and Noor, M.M. and Kadirgama, K. and Mamat, R. and Abdullah, A.A. (2019) The influence of formulation ratio and emulsifying settings on tri-fuel (diesel�ethanol�biodiesel) emulsion properties. Energies, 12 (9). ISSN 19961073

Aziz, A.R.A. and Hagos, F.Y. and Anbese, Y.T. and Heikal, M.R. and Firmansyah (2018) Application of the chain code and Fourier analysis techniques for the investigation of wrinkles and distortions on early flames. International Journal of Automotive and Mechanical Engineering, 15 (4). pp. 5709-5728. ISSN 22298649

Adam, I.K. and Heikal, M.R. and Aziz, A.R.A. and Othman, A.R. and Yusup, S. (2018) Combustion performance of rubber seed methyl ester using aromatic and phenolic antioxidants in a multi-cylinder diesel engine. Clean Technologies and Environmental Policy, 20 (10). pp. 2239-2253. ISSN 1618954X

El Adawy, M. and Heikal, M.R. and Aziz, A.R.A. and Munir, S. and Siddiqui, M.I. (2018) Effect of boost pressure on the in-cylinder tumble- motion of GDI engine under steady-state conditions using Stereoscopic-PIV. Journal of Applied Fluid Mechanics, 11 (3). pp. 733-742. ISSN 17353572

Mohammed, S.E. and Baharom, M.B. and Aziz, A.R.A. and Zainal, A.E.Z. and Firmansyah, F. (2018) Experimental investigation of ignition timing on the performance and emission characteristics of a crank-rocker engine. International Journal of Vehicle Structures and Systems, 10 (2). pp. 146-149. ISSN 09753060

Khan, M.Y. and Abdul Karim, Z.A. and Aziz, A.R.A. (2018) Experimental investigation of performance and emission characteristics of an idi diesel engine using homogenized water in diesel emulsion. International Journal of Mechanical and Production Engineering Research and Development, 8 (3). pp. 933-942. ISSN 22496890

Ismael, M.A. and Heikal, M.R. and Aziz, A.R.A. and Crua, C. and El-Adawy, M. and Nissar, Z. and Baharom, M.B. and Zainal, E.Z.A. and Firmansyah (2018) Investigation of puffing and micro-explosion of water-in-diesel emulsion spray using shadow imaging. Energies, 11 (9). ISSN 19961073

Adam, I.K. and Heikal, M. and Aziz, A.R.A. and Yusup, S. (2018) Mitigation of NOx emission using aromatic and phenolic antioxidant-treated biodiesel blends in a multi-cylinder diesel engine. Environmental Science and Pollution Research, 25 (28). pp. 28500-28516. ISSN 09441344

Chala, G.T. and Aziz, A.R.A. and Hagos, F.Y. (2018) Natural Gas Engine Technologies: Challenges and Energy Sustainability Issue. Energies, 11 (11). ISSN 19961073

Altaf, K. and Qayyum, J.A. and Rani, A.M.A. and Ahmad, F. and Megat-Yusoff, P.S.M. and Baharom, M. and Aziz, A.R.A. and Jahanzaib, M. and German, R.M. (2018) Performance analysis of enhanced 3D printed polymer molds for metal injection molding process. Metals, 8 (6). ISSN 20754701

Altaf, K. and Baharom, M. and Aziz, A.R.A. and Qayyum, J.A. and Jahanzaib, M. (2018) Rapid prototyping of a customized cooling system for a novel crank rocker engine. International Journal of Engineering and Technology(UAE), 7 (3). pp. 90-93. ISSN 2227524X

El-Adawy, M. and Heikal, M.R. and Aziz, A.R.A. and Siddiqui, M.I. and Wahhab, H.A.A. and Ismael, M.A. (2018) Tumble Motion Evolution for GDI Engine Using Particle Image Velocimetry (PIV). Journal of Mechanical Engineering, Specia (1). pp. 191-201. ISSN 18235514

Said, M.A. and Mun, L.K. and Aziz, A.R.A. (2018) Wall heat transfer analysis of internal combustion engine with free piston linear motion. International Journal of Engineering and Technology(UAE), 7 (3). pp. 141-144. ISSN 2227524X

Ismael, M.A. and Heikal, M.R. and Aziz, A.R.A. and Crua, C. (2018) The effect of fuel injection equipment of water-in-diesel emulsions on micro-explosion behaviour. Energies, 11 (7). ISSN 19961073

Ismael, M.A. and Heikal, M.R. and Aziz, A.R.A. and Syah, F. and Zainal A., E.Z. and Crua, C. (2018) The effect of fuel injection equipment on the dispersed phase of water-in-diesel emulsions. Applied Energy, 222. pp. 762-771. ISSN 03062619

Abdul Wahhab, H. and Aziz, A.R.A. and Al-Kayiem, H.H. and Nasif, M.S. (2017) Characteristics of CNG bubbles in Diesel flow under the influence of the magnetic field. Journal of Applied Fluid Mechanics, 10 (6). pp. 1649-1655. ISSN 17353572

El-Adawy, M. and Heikal, M.R. and Aziz, A.R.A. and Siddiqui, M.I. and Munir, S. (2017) Characterization of the inlet port flow under steady-state conditions using PIV and POD. Energies, 10 (12). ISSN 19961073

Abdalla, I.I. and Zainal A., E.Z. and Anwarudin, A.R.T. and Firmansyah and Aziz, A.R.A. and Heikal, M.R. (2017) Cogging force issues of permanent magnet linear generator for electric vehicle. Journal of Electrical Systems, 13 (3). pp. 489-502. ISSN 11125209

Chala, G.T. and Aziz, A.R.A. and Hagos, F.Y. (2017) Combined effect of boost pressure and injection timing on the performance and combustion of CNG in a DI spark ignition engine. International Journal of Automotive Technology, 18 (1). pp. 85-96. ISSN 12299138

Firmansyah and Aziz, A.R.A. and Heikal, M.R. and Zainal, E.Z.A. (2017) Diesel/CNG mixture autoignition control using fuel composition and injection gap. Energies, 10 (10). ISSN 19961073

Hagos, F.Y. and Aziz, A.R.A. and Sulaiman, S.A. and Firmansyah and Mamat, R. (2017) Effect of fuel injection timing of hydrogen rich syngas augmented with methane in direct-injection spark-ignition engine. International Journal of Hydrogen Energy, 42 (37). pp. 23846-23855. ISSN 03603199

El-Adawy, M. and Heikal, M.R. and Aziz, A.R.A. and Siddiqui, M.I. and Abdul Wahhab, H.A. (2017) Experimental study on an IC engine in-cylinder flow using different steady-state flow benches. Alexandria Engineering Journal, 56 (4). pp. 727-736. ISSN 11100168

Abdul Wahhab, H.A. and Aziz, A.R.A. and Al-Kayiem, H.H. and Nasif, M.S. (2017) Mathematical modeling of the flow of diesel-CNG fuel mixture in a pipe under the influence of a magnetic field. Journal of Applied Fluid Mechanics, 10 (1). pp. 389-396. ISSN 17353572

Abdulwahhab, H.A. and Aziz, A.R.A. and Al-Kayiem, H.H. and Nasif, M.S. (2017) Modeling of diesel- compressed natural gas bubbly flow under influencing of a magnetic field. Journal of Engineering Science and Technology, 12 (7). pp. 1930-1938. ISSN 18234690

Adam, I.K. and Aziz, A.R.A. and Heikal, M.R. and Yusup, S. (2017) Performance and Emission Analysis of Rubber Seed Methyl Ester and Antioxidant in a Multicylinder Diesel Engine. Energy and Fuels, 31 (4). pp. 4424-4435. ISSN 08870624

Mohammed, S.E. and Baharom, M.B. and Aziz, A.R.A. (2017) Performance and combustion characteristics of a novel crank-rocker engine. Journal of Mechanical Science and Technology, 31 (7). pp. 3563-3571. ISSN 1738494X

Wahhab, H.A.A. and Aziz, A.R.A. and Al-Kayiem, H.H. and Nasif, M.S. and Afolabi, L.O. (2017) Prediction of the phase distribution of diesel/CNG bubbly flow in a horizontal pipe under the influence of a magnetic field. Journal of Mechanical Science and Technology, 31 (11). pp. 5299-5309. ISSN 1738494X

Yahaya Khan, M. and Abdul Karim, Z.A. and Aziz, A.R.A. and Heikal, M.R. and Crua, C. (2017) Puffing and microexplosion behavior of water in pure diesel emulsion droplets during leidenfrost effect. Combustion Science and Technology, 189 (7). pp. 1186-1197. ISSN 00102202

Khalil, I. and Aziz, A.R.A. and Yusup, S. and Heikal, M. and El-Adawy, M. (2017) Response surface methodology for the optimization of the production of rubber seed/palm oil biodiesel, IDI diesel engine performance, and emissions. Biomass Conversion and Biorefinery, 7 (1). pp. 37-49. ISSN 21906815

Khan, M.Y. and Karim, Z.A.A. and Aziz, A.R.A. and Tan, I.M. (2017) A case study on the influence of selected parameters on microexplosion behavior of water in biodiesel emulsion droplets. Journal of Energy Resources Technology, Transactions of the ASME, 139 (2). ISSN 01950738

Ooi, B.L. and Gilbert, J.M. and Aziz, A.R.A. (2016) Analytical and finite-element study of optimal strain distribution in various beam shapes for energy harvesting applications. Acta Mechanica Sinica/Lixue Xuebao, 32 (4). pp. 670-683. ISSN 05677718

Ooi, B.L. and Gilbert, J.M. and Aziz, A.R.A. and Thein, C.K. (2016) Analytical modeling for switched damping electromagnetic energy harvester. Lecture Notes in Electrical Engineering, 379. pp. 1-12. ISSN 18761100

Abdul-Wahhab, H.A. and Aziz, A.R.A. and Al-Kayiem, H.H. and Nasif, M.S. (2016) CFD simulation of bubbly diesel-cng flow in a horizantal pipe under the influence of a magnetic field. ARPN Journal of Engineering and Applied Sciences, 11 (20). pp. 12122-12127. ISSN 18196608

Hagos, F.Y. and Aziz, A.R.A. and Sulaiman, S.A. (2016) Effect of injection timing on combustion, performance and emissions of lean-burn syngas (H2/CO) in spark-ignition direct-injection engine. International Journal of Engine Research, 17 (9). pp. 921-933. ISSN 14680874

Babiker, M.E. and Aziz, A.R.A. and Heikal, M.R. and Yusup, S. and Adam, A. (2016) Effects of enhancing cetane number of ethanol fumigation on diesel engine performance and emissions. ARPN Journal of Engineering and Applied Sciences, 11 (22). pp. 12994-12999. ISSN 18196608

Babiker, M.E. and Aziz, A.R.A. and Heikal, M. and Yusup, S. and Hagos, F.Y. (2016) Experimental and simulation study on steam gasification of phoenix-dactylifera date palm seeds. International Journal of Automotive and Mechanical Engineering, 13 (1). pp. 3201-3214. ISSN 22298649

Chuah, L.F. and Yusup, S. and Aziz, A.R.A. and Klemeš, J.J. and Bokhari, A. and Abdullah, M.Z. (2016) Influence of fatty acids content in non-edible oil for biodiesel properties. Clean Technologies and Environmental Policy, 18 (2). pp. 473-482. ISSN 1618954X

Adam, I.K. and Aziz, A.R.A. and Yusuf, S. (2016) Response surface methodology optimization of palm rubber seed combined oil based biodiesel and idi diesel engine performance and emission. ARPN Journal of Engineering and Applied Sciences, 11 (24). pp. 14195-14201. ISSN 18196608

Siddiqui, M.I. and Munir, S. and Heikal, M.R. and de Sercey, G. and Aziz, A.R.A. and Dass, S.C. (2016) Simultaneous velocity measurements and the coupling effect of the liquid and gas phases in slug flow using PIV�LIF technique. Journal of Visualization, 19 (1). pp. 103-114. ISSN 13438875

Opatola, R.A. and Aziz, A.R.A. and Heikal, M.R. and Said, M.A.M. (2016) Towards mitigating engine-out emissions: A migration to fuel based and combustion based solutions. ARPN Journal of Engineering and Applied Sciences, 11 (22). pp. 13435-13440. ISSN 18196608

Chuah, L.F. and Aziz, A.R.A. and Yusup, S. and Klemeš, J.J. and Bokhari, A. (2016) Waste cooking oil biodiesel via hydrodynamic cavitation on a diesel engine performance and greenhouse gas footprint reduction. Chemical Engineering Transactions, 50. pp. 301-306. ISSN 22839216

Mohammed, S.E. and Baharom, M.B. and Aziz, A.R.A. (2016) The effect of rocker ratio and connecting rod length on the performance of a crank-rocker mechanism with an extended rocker input link. ARPN Journal of Engineering and Applied Sciences, 11 (6). pp. 4221-4227. ISSN 18196608

Firmansyah and Aziz, A.R.A. and Heikal, M.R. and Abidin, E.Z.Z. (2016) The effect of wall temperature to the combustion of diesel/CNG mixture. ARPN Journal of Engineering and Applied Sciences, 11 (22). pp. 12923-12928. ISSN 18196608

Khan, M.Y. and Abdul Karim, Z.A. and Aziz, A.R.A. (2016) An experimental investigation of microexplosion in bio fuel emulsion. ARPN Journal of Engineering and Applied Sciences, 11 (24). pp. 14303-14307. ISSN 18196608

Adam, I.K. and Aziz, A.R.A. and Yusup, S. (2015) Determination of diesel engine performance fueled biodiesel (Rubber seed/palm oil mixture) diesel blend. International Journal of Automotive and Mechanical Engineering, 11 (1). pp. 2675-2685. ISSN 22298649

Zainal A., E.Z. and Ibrahim, A.A. and Aziz, A.R.A. and Zulkifli, S.A. (2015) Effect of motoring voltage on compression ratio of a free-piston linear generator engine. Journal of Mechanical Engineering and Sciences, 8. pp. 1393-1400. ISSN 22894659

Firmansyah and Aziz, A.R.A. (2015) Investigation of auto-ignition of octane-CNG mixture in HCCI engine. International Journal of Automotive and Mechanical Engineering, 11 (1). pp. 2235-2242. ISSN 22298649

Hagos, F.Y. and Aziz, A.R.A. and Sulaiman, S.A. (2015) Investigation of deposit formation in direct-injection spark-ignition engine powered on syngas. International Journal of Automotive Technology, 16 (3). pp. 479-485. ISSN 12299138

Hagos, F.Y. and Aziz, A.R.A. and Sulaiman, S.A. (2015) Methane enrichment of syngas (H2/CO) in a spark-ignition directinjection engine: Combustion, performance and emissions comparison with syngas and Compressed Natural Gas. Energy, 90. pp. 2006-2015. ISSN 03605442

Zulkifli, S.A. and Mohd, S. and Saad, N. and Aziz, A.R.A. (2015) Operation and control of split-parallel, through-theroad hybrid electric vehicle with in-wheel motors. International Journal of Automotive and Mechanical Engineering, 11 (1). pp. 2793-2808. ISSN 22298649

Chuah, L.F. and Aziz, A.R.A. and Yusup, S. and Bokhari, A. and Klemeš, J.J. and Abdullah, M.Z. (2015) Performance and emission of diesel engine fuelled by waste cooking oil methyl ester derived from palm olein using hydrodynamic cavitation. Clean Technologies and Environmental Policy, 17 (8). pp. 2229-2241. ISSN 1618954X

Ooi, B.L. and Gilbert, J.M. and Aziz, A.R.A. (2015) Switching damping for a frequency-tunable electromagnetic energy harvester. Sensors and Actuators, A: Physical, 234. pp. 311-320. ISSN 09244247

Khan, M.Y. and Abdul Karim, Z.A. and Aziz, A.R.A. and Tan, I.M. (2015) A case study on preparation, stability and physical properties of water in diesel emulsion. ARPN Journal of Engineering and Applied Sciences, 10 (22). pp. 17289-17293. ISSN 18196608

Yahaya Khan, M. and Abdul Karim, Z.A. and Hagos, F.Y. and Aziz, A.R.A. and Tan, I.M. (2014) Current trends in water-in-diesel emulsion as a fuel. The Scientific World Journal, 2014. ISSN 1537744X

Mohammed, S.E. and Baharom, M.B. and Aziz, A.R.A. (2014) Estimation of counterweight for shaking force balancing of a crank-rocker mechanism. Applied Mechanics and Materials, 663. pp. 135-140. ISSN 16609336

Khan, M.Y. and Abdul Karim, Z.A. and Aziz, A.R.A. and Tan, I.M. (2014) Experimental investigation of microexplosion occurrence in water in diesel emulsion droplets during the leidenfrost effect. Energy and Fuels, 28 (11). pp. 7079-7084. ISSN 08870624

Zulkifli, S.A. and Mohd, S. and Saad, N. and Aziz, A.R.A. (2014) Impact of motor size &efficiency on acceleration, Fuel consumption &Emissions of split- axle through- the- road parallel hybrid electric vehicle. Applied Mechanics and Materials, 663. pp. 498-503. ISSN 16609336

Umar, A.A. and Umar, U.H. and Ahmad, M. and Zawawi, N.A.W.A. and Aziz, A.R.A. (2014) STEMMING WATER-RELATED DEATHS IN SUB-SAHARAN AFRICA: THE PLACE OF ISLAMIC PROJECT FINANCE AND MALAYSIAN CONTRACTORS. ISRA International Journal of Islamic Finance, 6 (2). pp. 87-113. ISSN 01281976

Hagos, F.Y. and Aziz, A.R.A. and Sulaiman, S.A. (2014) Syngas (H2/CO) in a spark-ignition direct-injection engine. Part 1: Combustion, performance and emissions comparison with CNG. International Journal of Hydrogen Energy, 39 (31). pp. 17884-17895. ISSN 03603199

Hagos, F.Y. and Aziz, A.R.A. and Sulaiman, S.A. (2014) Trends of syngas as a fuel in internal combustion engines. Advances in Mechanical Engineering, 2014. ISSN 16878132

Ayandotun, W.B. and Aziz, A.R.A. and Heikal, M.R. (2014) The effect of high carbon dioxide content on the performance and emission characteristics of a Direct Injection (DI) compressed natural gas engine. Applied Mechanics and Materials, 663. pp. 64-70. ISSN 16609336

Hagos, F.Y. and Aziz, A.R.A. and Sulaiman, S.A. (2013) Combustion characteristics of direct-injection spark-ignition engine fuelled with producer gas. Energy Education Science and Technology Part A: Energy Science and Research, 31 (3). pp. 1683-1698. ISSN 1308772X

Firmansyah and Aziz, A.R.A. and Heikal, M.R. (2013) Double stage wiebe: An approach to single zone modeling of dual fuel HCCI combustion. Asian Journal of Scientific Research, 6 (2). pp. 388-394. ISSN 19921454

Hamada, K.I. and Rahman, M.M. and Aziz, A.R.A. (2013) Parametric study of instantaneous heat transfer based on multidimensional model in direct-injection hydrogen-fueled engine. International Journal of Hydrogen Energy, 38 (28). pp. 12465-12480. ISSN 03603199

Anbese, Y.T. and Aziz, A.R.A. and Heikal, M.R. (2012) Characteristics of induction flow in SI direct injection engine with dual variable Swirl Control Valve. Journal of Applied Sciences, 12 (24). pp. 2534-2540. ISSN 18125654

Shahzad, R. and Naveenchandran, P. and Aziz, A.R.A. (2012) Characteristics of lean and stoichiometric combustion of compressed natural gas in a direct injection engine. Applied Mechanics and Materials, 110-11. pp. 357-369. ISSN 16609336

Hagos, F.Y. and Aziz, A.R.A. and Sulaiman, S.A. and Firmansyah (2012) Combustion characteristics of late injected CNG in a spark ignition engine under lean operating condition. Journal of Applied Sciences, 12 (23). pp. 2368-2375. ISSN 18125654

Hamada, K.I. and Rahman, M.M. and Aziz, A.R.A. (2012) Development of a computational fluid dynamics model for direct injection hydrogen fueled engine. International Review of Mechanical Engineering, 6 (3). pp. 675-679. ISSN 19708734

Hamada, K.I. and Rahman, M.M. and Aziz, A.R.A. (2012) Influence of engine speed and mixture strength on instantaneous heat transfer for direct injection hydrogen fuelled engine. Energy Education Science and Technology Part A: Energy Science and Research, 30 (SPEC .). pp. 153-172. ISSN 1308772X

Abidin, E.Z.Z. and Ibrahim, A.A. and Aziz, A.R.A. and Zulkifli, S.A. (2012) Investigation of starting behaviour of a free-piston linear generator. Journal of Applied Sciences, 12 (24). pp. 2592-2597. ISSN 18125654

Hamada, K.I. and Rahman, M.M. and Aziz, A.R.A. (2012) Multidimensional computational modeling of direct injection for hydrogen fueled engine. Advanced Science Letters, 13. pp. 317-321. ISSN 19366612

Hamada, K.I. and Rahman, M.M. and Aziz, A.R.A. (2012) Time-averaged heat transfer correlation for direct injection hydrogen fueled engine. International Journal of Hydrogen Energy, 37 (24). pp. 19146-19157. ISSN 03603199

Mohammed, S.E.L. and Baharom, M.B. and Aziz, A.R.A. (2011) Analysis of engine characteristics and emissions fueled by in-situ mixing of small amount of hydrogen in CNG. International Journal of Hydrogen Energy, 36 (6). pp. 4029-4037. ISSN 03603199

al-Khairi, N.N. and Naveenchandran, P. and Aziz, A.R.A. (2011) Comparison of HCCI and SI characteristics on low load CNG-DI combustion. Journal of Applied Sciences, 11 (10). pp. 1827-1832. ISSN 18125654

Noran, N.K. and Naveenchandran, P. and Aziz, A.R.A. (2011) Comparison of HCCI and SI combustion of direct injected CNG at low load condition. SAE Technical Papers. ISSN 01487191

Naveenchandran, P. and Al-Khairi, N. and Shahzad, R. and Aziz, A.R.A. (2011) Effect of exhaust gas recirculation on the dual fuel combustion of gasoline and CNG by compression ignition. Journal of Applied Sciences, 11 (11). pp. 2030-2035. ISSN 18125654

Anbese, Y.T. and Aziz, A.R.A. and Karim, Z.A.B.A. (2011) Flame development study at variable swirl level flows in a stratified CNG DI combustion engine using image processing technique. Journal of Applied Sciences, 11 (10). pp. 1698-1706. ISSN 18125654

Iffa, E.D. and Aziz, A.R.A. and Malik, A.S. (2011) Gas flame temperature measurement using background oriented schlieren. Journal of Applied Sciences, 11 (9). pp. 1658-1662. ISSN 18125654

Mohammed, S.E. and Iffa, E.D. and Baharom, M.B. and Aziz, A.R.A. (2011) Spray characteristic comparisons of compressed natural gas and hydrogen fuel using digital imaging. Journal of Applied Sciences, 11 (9). pp. 1624-1629. ISSN 18125654

Iffa, E.D. and Aziz, A.R.A. and Malik, A.S. (2011) Velocity field measurement of a round jet using quantitative schlieren. Applied Optics, 50 (5). pp. 618-625. ISSN 1559128X

Mohammed, S.E. and Baharom, M.B. and Aziz, A.R.A. and Firmansyah (2011) The effects of fuel-injection timing at medium injection pressure on the engine characteristics and emissions of a CNG-DI engine fueled by a small amount of hydrogen in CNG. International Journal of Hydrogen Energy, 36 (18). pp. 11997-12006. ISSN 03603199

Wasiu, S.O. and Sulaiman, S.A. and Aziz, A.R.A. (2011) An experimental study of different effects of EGR rates on the performance and exhaust emissions of the stratified charge piston direct injection compressed natural gas engine. Journal of Applied Sciences, 11 (9). pp. 1479-1490. ISSN 18125654

Ibrahim, A.A. and Aziz, A.R.A. and Abidin, E.Z.B.Z. and Saiful, Z.A. (2011) The operation of free piston linear generator engine using MOSFET and IGBT drivers. Journal of Applied Sciences, 11 (10). pp. 1791-1796. ISSN 18125654

Aziz, A.R.A. and Firmansyah and Shahzad, R. (2010) Combustion analysis of a cng direct injection spark ignition engine. International Journal of Automotive and Mechanical Engineering, 2 (1). pp. 157-170. ISSN 22298649

Iffa, E.D. and Aziz, A.R.A. and Malik, A.S. (2010) Concentration measurement of injected gaseous fuel using quantitative schlieren and optical tomography. Journal of the European Optical Society, 5. ISSN 19902573

Tadesse, G. and Aziz, A.R.A. (2009) Effect of boost pressure on engine performance and exhaust emissions in direct-injection compressed natural gas (CNG-DI) spark ignition engine. SAE Technical Papers. ISSN 01487191

Iffa, E.D. and Aziz, A.R.A. (2009) Variable density distribution of CNG jet injected at small injection pressure. SAE Technical Papers. ISSN 01487191

Conference or Workshop Item

Bashir, A. and Zulkifli, S.A. and Abidin, E.Z.Z. and Aziz, A.R.A. (2020) Control of Piston Trajectory in a Free-Piston Linear Electric Generator by Load Current Modulation. In: UNSPECIFIED.

Arman, A. and Hagos, F.Y. and Abdullah, A.A. and Mamat, R. and Aziz, A.R.A. and Cheng, C.K. (2020) Syngas production through steam and CO2 reforming of methane over Ni-based catalyst-A Review. In: UNSPECIFIED.

Abdul Wahhab, H.A. and Aziz, A.R.A. and Al-Kayiem, H.H. and Nasif, M.S. and Reda, M.N. (2018) Application of Electromagnetic Induction Technique to Measure the Void Fraction in Oil/Gas Two Phase Flow. In: UNSPECIFIED.

Jaffry, M.N.M. and Abdul Karim, Z.A. and Ramlan, N.A. and Mohammed, S.E. and Zainal, E.Z. and Firmansyah and Ahmad, A.S. and Baharom, M.B. and Heikal, M.R. and Aziz, A.R.A. (2018) Bouncing phenomena of free piston linear generator at starting process. In: UNSPECIFIED.

El-Adawy, M. and Heikal, M.R. and Aziz, A.R.A. and Ismeal, M.A. and Wahhab, H.A.A. (2018) Characterization of the effect of pressure difference on in-cylinder flow field using proper orthogonal decomposition (POD). In: UNSPECIFIED.

Firmansyah and Morgan, R. and Heikal, M.R. and Aziz, A.R.A. (2018) Effect of pressure in crossover port to the in-cylinder flow of split-cycle engine. In: UNSPECIFIED.

Mohammed, S.E. and Ramlan, N.A. and Aziz, A.R.A. and Firmansyah, F. and Ezrann Zainal, Z. (2018) Investigation of late fuel injection position on the combustion of free piston engine. In: UNSPECIFIED.

Masri, M.M. and Evelyn, E. and Ahmad, A.S. and Tamili, S.N.A. and Abidin, E.Z.Z. and Firmansyah, F. and Aziz, A.R.A. and Heikal, M.R. (2018) Investigation on intake manifold volume in free-piston linear generator engine. In: UNSPECIFIED.

Wahhab, H.A.A. and Aziz, A.R.A. and Al-Kayiem, H.H. and Nasif, M.S. and El-Adawy, M. (2018) Magneto-hydrodynamics of bubbly flow in horizontal pipe: New criteria through numerical simulation. In: UNSPECIFIED.

Al-Kayiem, H.H. and Wahhab, H.A.A. and Magaril, E. and Aziz, A.R.A. (2018) Performance and emissions investigation of a single cylinder diesel engine using enhanced blend biodiesel by nanoparticles. In: UNSPECIFIED.

Kardan, R. and Baharom, M.B. and Mohammed, S.E. and Aziz, A.R.A. and Zainal, A.E.Z. and Firmansyah (2018) The effect of engine throttle position on the performance characteristics of a crank-rocker engine fitted with a conventional cylinder head. In: UNSPECIFIED.

Ismael, M.A. and Heikal, M.R. and Aziz, A.R.A. and Crua, C. and El-Adawy, M. (2018) The effect of unstable emulsion of water-in-diesel on micro-explosion phenomena. In: UNSPECIFIED.

Tamili, S.N.A. and Aziz, A.R.A. and Sulaiman, S.A. and Zainal, E.Z. and Firmansyah and Heikal, M.R. (2018) A review on free piston linear engine (FPLE). In: UNSPECIFIED.

Evelyn, E. and Aziz, A.R.A. and Firmansyah, F. and Abidin, E.Z.Z. (2018) A review on the operating characteristics of free piston engine and its recent developments. In: UNSPECIFIED.

Abdalla, I.I. and Zainal, A.E.Z. and Ramlan, N.A. and Firmansyah and Aziz, A.R.A. and Heikal, M.R. (2017) Cogging force investigation of a free piston permanent magnet linear generator. In: UNSPECIFIED.

Abdalla, I. and Zainal, E.Z.A. and Ramlan, N.A. and Firmansyah and Aziz, A.R.A. and Heikal, M. (2017) Free piston linear generator for low grid power generation. In: UNSPECIFIED.

Foong, F.M. and Thein, C.K. and Ooi, B.L. and Aziz, A.R.A. (2017) A low-cost vibration analyser for analogue electromagnetic shaker. In: UNSPECIFIED.

Zulkifli, S.A. and Saad, N. and Aziz, A.R.A. (2016) Comparative Analysis of Torque and Acceleration of Pre- and Post-Transmission Parallel Hybrid Drivetrains. In: UNSPECIFIED.

Zulkifli, S.A. and Saad, N. and Aziz, A.R.A. (2016) Deterministic and fuzzy logic control of through-the-road split-parallel hybrid electric vehicle. In: UNSPECIFIED.

Siddiqui, M.I. and Aziz, A.R.A. and Heikal, M.R. (2016) Dynamics of liquid slug using particle image velocimetry technique. In: UNSPECIFIED.

Ooi, B.L. and Gilbert, J.M. and Aziz, A.R.A. (2016) Frequency-tunable electromagnetic energy harvester by means of damping switching. In: UNSPECIFIED.

Zulkifli, S.A. and Syaifuddin Mohd, M. and Maharun, M. and Bakar, N.S.A. and Idris, S. and Samsudin, S.H. and Firmansyah, F. and Adz, J.J. and Misbahulmunir, M. and Abidin, E.Z.Z. and Syafiq Mohd, M. and Saad, N. and Aziz, A.R.A. (2015) Design and development of split-parallel through-the road retrofit hybrid electric vehicle with in-wheel motors. In: UNSPECIFIED.

Zulkifli, S.A. and Mohd, S. and Jamali, A.J. and Kurniawan, Y. and Saad, N. and Aziz, A.R.A. (2015) Implementation of energy management system for a split-parallel hybrid electric vehicle with in-wheel motors. In: UNSPECIFIED.

Abdul-Wahhab, H.A. and Aziz, A.R.A. and Al-Kayiem, H.H. and Nasif, M.S. (2015) Modeling of diesel/CNG mixing in a pre-injection chamber. In: UNSPECIFIED.

Zulkifli, S.A. and Mohd, S. and Saad, N. and Aziz, A.R.A. (2015) Operation, power flow, system architecture and control challenges of split-parallel through-the-road hybrid electric vehicle. In: UNSPECIFIED.

Zulkifli, S.A. and Mohd, S. and Saad, N. and Aziz, A.R.A. (2015) Split-parallel through-the-road hybrid electric vehicle: Operation, power flow and control modes. In: UNSPECIFIED.

Munir, S. and Heikal, M.R. and Aziz, A.R.A. and Muthuvalu, M.S. and Siddiqui, M.I. (2015) Temporal and spatial characterization of turbulent structures in liquid phase using POD technique. In: UNSPECIFIED.

Firmansyah and Aziz, A.R.A. and Heikal, M.R. (2015) The combustion behavior of diesel/CNG mixtures in a constant volume combustion chamber. In: UNSPECIFIED.

Ooi, B.L. and Aziz, A.R.A. and Gilbert, J.M. (2014) Analytical and numerical modelling for dual-resonator vibration-based electromagnetic generator. In: UNSPECIFIED.

Karim, Z.A.A. and Khan, M.Y. and Aziz, A.R.A. and Tan, I.M. (2014) Characterization of water in diesel emulsion. In: UNSPECIFIED.

Hagos, F.Y. and Aziz, A.R.A. and Sulaiman, S.A. (2014) Effect of air-fuel ratio on the combustion characteristics of syngas (H2:CO) in direct-injection spark-ignition engine. In: UNSPECIFIED.

Zulkifli, S.A. and Asirvadam, V.S. and Saad, N. and Aziz, A.R.A. and Mohideen, A.A.M. (2014) Implementation of electronic throttle-by-wire for a hybrid electric vehicle using National Instruments' CompactRIO and LabVIEW Real-Time. In: UNSPECIFIED.

Zawawi, N.A.W.A. and Umar, A.A. and Aziz, A.R.A. and Crouzier, O. and Khamidi, M.F. and Idrus, A. (2014) PFI procurement skills: A cross-sector survey of practitioners. In: UNSPECIFIED.

Khan, M.Y. and Abdul Karim, Z.A. and Aziz, A.R.A. and Tan, I.M. (2014) Performance and emission assessment of multi cylinder diesel engine using surfactant enhanced water in diesel emulsion. In: UNSPECIFIED.

Adam, I.K. and Aziz, A.R.A. and Yusup, S. (2014) Performance and emission characteristics of an idi diesel engine fuelled biodiesel (Rubber Seed Oil and Palm Oil Mix) diesel blends. In: UNSPECIFIED.

Wasiu, A.B. and Aziz, A.R.A. and Heikal, M.R. (2014) The effect of injection timing on the performance of natural gas with a high carbon dioxide (CO2) content in a Direct Injection (DI) gas engine. In: UNSPECIFIED.

Babiker, M.E. and Aziz, A.R.A. and Heikal, M. and Yusup, S. (2014) The pyrolysis behavior of evolved species from date palm seeds. In: UNSPECIFIED.

Opatola, R.A. and Aziz, A.R.A. and Heikal, M.R. and Said, M.A.M. (2014) A review of the utilisation of natural gas with high carbon dioxide content as automotive fuel in an indirect injection diesel engine. In: UNSPECIFIED.

Hagos, F.Y. and Aziz, A.R.A. and Sulaiman, S.A. (2013) Early flame development image comparison of low calorific value syngas and CNG in di SI gas engine. In: UNSPECIFIED.

Zulkifli, S.A. and Mohd, S. and Saad, N. and Aziz, A.R.A. (2013) Influence of motor power and efficiency on fuel consumption of retrofit-conversion split-parallel hybrid electric vehicle. In: UNSPECIFIED.

Zulkifli, S.A. and Mohd, S. and Saad, N. and Aziz, A.R.A. (2013) Influence of motor size and efficiency on acceleration, fuel economy and emissions of split-parallel hybrid electric vehicle. In: UNSPECIFIED.

Zulkifli, S.A. and Mohd, S. and Maharun, M. and Saad, N. and Aziz, A.R.A. (2012) Development of a retrofit split-axle parallel hybrid electric vehicle with in-wheel motors. In: UNSPECIFIED.

Zulkifli, S.A. and Saad, N. and Mohd, S. and Aziz, A.R.A. (2012) Split-parallel in-wheel-motor retrofit hybrid electric vehicle. In: UNSPECIFIED.

Ali, Y. and Shamsudeen, A. and Abdullah, S. and Aziz, A.R.A. (2012) The effect of spray angles of the injector on the power of compressed natural gas direct injection (CNGDI) engine. In: UNSPECIFIED.

Hagos, F.Y. and Aziz, A.R.A. and Tan, I.M. (2011) Water-in-diesel emulsion and its micro-explosion phenomenon-review. In: UNSPECIFIED.

Zulkifli, S.A. and Karsit, M.N. and Aziz, A.R.A. (2008) Rectangular current commutation and open-loop control for starting of a free-piston linear engine-generator. In: UNSPECIFIED.

Zulkifli, S.A. and Karsiti, M.N. and Aziz, A.R.A. (2008) Starting of a free-piston linear engine-generator by mechanical resonance and rectangular current commutation. In: UNSPECIFIED.

Book

Aziz, A.R.A. and Baharom, M.B. and Abidin, E.Z.Z. and Firmansyah and Mohammed, S.E. and Nadhari, W.N.A.W. and Evelyn and Jaffry, M.N.M. (2019) Principal, design and characteristics of a free piston linear generator. Springer Singapore, pp. 127-144. ISBN 9789811501029; 9789811501012

Dalha, I.B. and Said, M.A. and Abdul Karim, Z.A. and Aziz, A.R.A. and Firmansyah and Abidin, E.Z.Z. and Ismael, M.A. (2019) Reactivity controlled compression ignition: An advanced combustion mode for improved energy efficiency. Springer Singapore, pp. 101-126. ISBN 9789811501029; 9789811501012

Aziz, A.R.A. and Ismael, M.A. and Heikal, M. and Firmansyah and Dalha, I.B. and Abidin, E.Z.Z. (2019) Water in diesel emulsion behavior in high-pressure direct injection system. Springer Singapore, pp. 85-99. ISBN 9789811501029; 9789811501012

Lee, O.B. and Ket, T.C. and Keat, Y.C. and Aziz, A.R.A. (2016) Applications of vibration-based energy harvesting (VEH) devices. IGI Global, pp. 989-1014. ISBN 9781522516729; 1522516719; 9781522516712